Just How to Replace a Bathtub Yourself: Removing and Replacing.
Just How to Replace a Bathtub Yourself: Removing and Replacing.
Blog Article
What're your beliefs about How to Install a Bathtub Yourself?
Installing a bath tub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub as well as place the new bath tub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the task and also are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is far better to consider utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your restroom if you have actually currently bought a new tub and also do not need to alter the plan of your previous water pipes.
Your tools as well as product checklist need to comprise the following:
Planning for the Installation
First of all, the sustaining structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The process of removing the existing taps can be fairly bothersome due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the needed position. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the bath tub has been utilized at the very least once as this will resolve it right into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind needs to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a rigid seal, causing the water to permeate the wall between the bath and the tiling, resulting in issues with wetness and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently offered on the market. It is recommended to fit the tiles making use of waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that report about Installing A Bathtub through an acquaintance on a different blog. Sharing is caring. You just don't know, you may be helping someone out. Thank you so much for going through it.
Book An Appointment Report this page